Adding some CA can also better secure the bond. The end result should look like the picture. Locate the two 1x480mm control rods, Z-bend wires, and two small pieces of heat shrink.Ĭoat the tip of the push rods with FoamTac, slide the Z-bend wires and heat shrink together within the rod, and shrink the wrap with heat. Once satisfied with the fit, Glue into place and glue the spar as well. Make sure that it is perpendicular to the horizontal fuse.ĭouble check the back as well. Locate the upper half of the vertical fuse. The rod should stick out of the fuse as shown. Slide the spar into the lower half of the vertical fuse as shown. Locate the 3x0.5x160mm vertical fuse spar. Tip: I use hot glue for servo horns because it allows the servos to be easily removed with acetone i needed. Make sure that the servos are seated down in the slots. Note: The push rod guides can be attached to the upper side of the outer hole of the horns as well before installation for convenience. Install the servos into their appropriate slot. These servos will be for the elevator and rudder. Wrap the horns together with thread ans apply CA. Thread is highly recommended when attaching.ĬA the extension horns onto the servo horns WITHOUT getting CA in the servo spline. Now it is time to secure the extension horns onto the servo horns. For maximum throw, assemble through the outer hole of the horn. Locate the four servo horn extension horns and push rod guide assemblies as shown.Īssemble the push rod guides as shown. Sit the model up on the rods and make sure it sits level. Slide the slots through the guides and fuse as shown. In order to make sure that the two fuses are perpendicular, some trimming may be required for some of the rods. Test fit the 0.8x130mm rods into the appointed slots as shown. Test fit the 1x155mm rods in the appointed slots as shown. Locate the ten 0.8x130mm (fuse bracing), two 1x155mm (front bracing), and two 2x185mm (Landing gear) rods. Make sure it is also perpendicular in the back. Make sure that the lower half of the vertical fuse is perpendicular to the horizontal fuse. Locate the lower half of the vertical fuse. Weight down the fuse and allow time to dry. Make sure the rods are flush with the foam. CA the horn.Īfter testing that the elevator moves properly, locate the two 0.8圆25mm rods. ALSO DO NOT GLUE THE ROD TO THE FOAM OF THE FUSE. CA the inner guides to the foam BUT DO NOT CA TO THE ROD. CA the outer guides into the foam and Outer elevator spar to the elevator halves. IMPORTANT STEP: Once happy with the test fit. Also ensure that the rod guides are flush. Make sure that the elevator horn is perpendicular to the surface. Make sure that the elevator rod is evenly seated in the sot. Test fit the elevator rod, rod guides, and elevator horn into the appointed slots. Install the pushrod guide as shown in the middle hole of the elevator horn.Īssemble as shown. Locate the elevator assembly and the 3x326 elevator rod as shown. Accelerator can be used to speed up the process. Once satisfied, glue into place with CA and allow time to dry. Test fit into their appointed slots in the ailerons like shown. Locate the sixteen 0.8x155mm aileron reinforcement rods. Glue the other horns in the appointed slots in the top wing. Test fit the horns into the lower wing (recognized by the two larger slots for the aileron servos) and assure that they seat in their appointed slots correctly. Once satisfied, glue into place with FoamTac. Test fit and assure that the spar is flush with the foam. Test fit and assure that they sit perpendicular to the aileron surface. remove the foam tab to reveal their appointed slots in the ailerons. Weight down the joints and allow time to dry. Locate the upper and lower wing halves and glue together with a thin bead of FoamTac. Now is also a good time to organize and group the carbon rods for convenience. Now is a good time to test electronics, center servos, calibrate ESC, check motor direction, and bind the model. Unfortunately, due to the Global Economic Meltdown, psychotic left-wing “Green” extremism and hypocritical Government corruption, it turns out Catharsis isn’t a much better place to live.With the box on the the table, let's get started:)įold the surfaces and weight down on a flat surface for about an hour or so to loosen up the hinges. About This Game Good or Insane? The choice is yours.įollowing the Apocalyptic end to the Postal Dude’s week in Paradise, we follow him and his insane pitbull Champ as they emigrate to its appropriately named sister city, Catharsis.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |